Pipe Repair in Ruby, SC — Located Precisely, Fixed Permanently
Pipe failures range from a slow pinhole leak weeping inside a wall to a full main line rupture. Locating the failure precisely — before opening drywall or digging — is the skill that separates a clean, affordable repair from an expensive and destructive guessing operation. Masters Plumbing Service's pipe technicians in Ruby, SC use acoustic listening devices and thermal imaging cameras to find the leak first, then open only what needs to be opened.
What Separates Precision Pipe Repair from Guesswork
Our techs work on every pipe material found in Ruby, SC homes, from pre-1970s galvanized to modern PEX-A crosslinked systems. The repair method matches the pipe.
🔊
Acoustic Leak Detection
Acoustic detection is most effective on pressurized supply lines. Combined with a pressure test to confirm water loss before we start, it tells us both that there's a leak and exactly where it is.
🌡️
Thermal Camera Scanning
Active water leaks create temperature differentials on wall and floor surfaces detectable with an infrared camera. A slow leak inside a wall shows as a cold, spreading zone; a hot water line leak shows the inverse. Thermal imaging confirms leak presence and approximate location before any cutting begins.
🛠️
All Pipe Materials & Joining Methods
Press-fit copper connections — particularly useful for repairs in occupied spaces where open flame is a concern — are available as an alternative to torch sweating where code permits.
🔒
Pressure-Tested Before We Leave
Drain line repairs are water-tested by running fixtures through the repaired section and visually confirming no seepage at the repair joint and downstream.
Our Pipe Repair Services
What We Fix — Pipe by Pipe, Material by Material
Pipe failures have different causes depending on material type, age, water chemistry, and installation history. Here's how we address each category.
Copper
Copper Pipe Repair & Repipe
Pitting corrosion in copper is sometimes systemic rather than localized — a single pinhole is often the first of several to appear. When the camera or pressure test finds multiple deteriorated sections, we give you an honest assessment of whether targeted repair or full copper repipe is the better long-term answer.
Galvanized
Galvanized Pipe Replacement
We replace galvanized supply lines with copper or PEX — either as targeted section replacement at active failure points or as a full-house repipe project. We connect the new material to existing fittings using dielectric unions where code requires to prevent galvanic corrosion at copper-to-galvanized transitions.
PEX
PEX Pipe Repair & Extension
Cross-linked polyethylene (PEX) is the current standard for residential supply piping. Failures are uncommon but occur at crimp or clamp fittings that were improperly installed, at pipe runs exposed to UV degradation, or at locations where the pipe was kinked during installation. We repair using expansion fittings (for PEX-A) or crimp fittings with the correct ring size for the pipe diameter.
Burst Pipes
Burst & Freeze-Damaged Pipe Repair
We also inspect upstream of the burst for additional sections that froze but haven't yet failed — because a partially-thawed line sometimes shows multiple failure points only after pressure is restored.
Slab Leaks
Under-Slab Pipe Leak Repair
Slab leak rerouting is often more cost-effective than direct access, particularly for longer runs or under tiled floors. We present the options honestly with pricing so you can choose based on your priorities.
Full Repipe
Whole-House Repipe Service
When galvanized supply lines are at end of life or polybutylene pipe (recalled for chronic failure) is in the home, a full repipe with PEX or copper is the permanent solution. We run new supply lines through the structure, transition all fixture connections, pressure test the entire new system, and patch access points in walls and ceilings.
Here's how a Masters Plumbing Service pipe repair call plays out in Ruby, SC.
1
Call & Describe — We Shut the Water If Needed
Active leak? Our dispatcher walks you through shutting off the main supply valve while we drive to you. Describing what you see — water stain on a ceiling, drop in water pressure, wet flooring — helps us arrive with the right detection tools loaded.
2
Pressure Test & Acoustic / Thermal Detection
We pressurize the supply system and monitor for pressure drop to confirm an active leak. Then acoustic listening devices and the thermal camera locate the failure to within a small area — telling us which section of wall, floor, or slab to open.
3
Flat-Rate Quote & Minimal Access Opening
For slab leaks, we present repair, reroute, and lining options with pricing so you can make an informed choice before any concrete is cut.
4
Repair & Pressure Test — Then You're Done
You receive a written summary of what failed, what we installed, and the warranty terms before we leave.
Customer Reviews
What Ruby Customers Say About Our Pipe Work
★★★★★
My older home had a copper supply line fail inside an exterior wall. The thermal camera showed the wet zone through the drywall without any cutting. They opened a 10-inch section right at the pinhole, put in a press-fit repair coupling — no torch in my wall — pressure tested, and patched the drywall themselves. Two hours total.
— N. Bergman, Ruby
★★★★★
Our galvanized supply lines finally gave out — low pressure everywhere, rust-colored water at some fixtures. Masters Plumbing Service repiped the whole house with PEX over two days. They confirmed pressure and flow at every fixture before leaving, patched all the wall access points smooth, and cleaned up each work area. One year later, no issues at all.
— O. & R. Adeyemi, Ruby, SC
★★★★★
I noticed my water meter spinning with all fixtures off — confirmed a leak in the supply system. Masters Plumbing Service ran a pressure test and acoustic scan, found a pinhole in a copper section under the slab in the utility room. They rerouted the line through the wall above slab, tested, and closed out the permit. The reroute was exactly the same cost as direct slab access would have been, but no damaged floor tile.
— F. Okoro, Ruby, SC
Common Questions
Pipe Repair Questions We Answer Every Day
A slow pinhole leak inside a wall can run for months before surface damage appears. By the time you see a stain, the moisture intrusion is typically already significant. If your meter shows movement with everything off, call us — we can pressure-test and locate it before it becomes a major remediation project.
In some cases — particularly for older copper systems with multiple pinhole failures along a supply run — rerouting the line through accessible framing rather than repairing it in place is more practical and more permanent. We present both options when they're both viable.
A slab leak is a supply line or drain line failure in a pipe that runs through or under the concrete foundation slab. Supply line slab leaks are the more urgent scenario — pressurized water escaping under the slab saturates the subgrade, can undermine the foundation, and drives significant water bills.
We assess galvanized condition when we're on-site — visible exterior corrosion, interior scale visible at the cut failure point, and water pressure readings all tell us how advanced the system deterioration is. We give you the repair-vs-repipe math honestly so you can make the decision that fits your timeline and budget.
A single localized pipe repair — finding and fixing one failure point — typically takes 1.5–3 hours including detection, access, repair, and pressure testing. Slab leak reroutes run 3–5 hours depending on the routing path and pipe length. A full-house repipe is a multi-day project — typically 2–4 days for a standard single-family home depending on size and pipe count.
Our pipe repair quote includes clean access cuts and leaving the opening ready for patching — with a clean, straight cut that accepts a standard drywall patch. We can typically patch the access opening as part of the job on request, though finish painting and texture matching are typically handled by the homeowner or a drywall contractor for best cosmetic results.
Service Area
Masters Plumbing Service Pipe Techs Serving Ruby, SC
Masters Plumbing Service dispatches pipe repair technicians throughout Ruby and the broader Ruby, SC service area. Same-day service is available on most calls. Emergency burst pipe response is available 24 hours a day.
